Net Lab

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Perenio PEACG01 ======
{{hardware:perenio:150099243-31c2f1db-1cf8-43c3-a6b1-5d4eacec24d8.png?200|}}\\

Based on refence design: CUS531MP3-NAND\\

===== Hardware ===== 
  * CPU: QCA4531-BL3A
  * RAM: winbond W9751G6KB-25 (DDR-2, 64MB)
  * SPI Flash: mx25l3205d (512KB)
  * NAND Flash: Macronix MX35LF1G4EAB (SLC, 128MB)
  * USB Hub: GL850G
  * USB-Serial: PL2303SA
  * Clock: PCF8563 + Battery
  * ZigBee: EFR32 MG1P232GG
  * 802.11bgn 2T2R
  * 1x 10/100/1000 Mbps Ethernet port
  * 3 leds
  * 2 buttons
  * UART header on PCB (115200 8n1)
  * U-Boot bootloader @ SPI flash



===== Photos =====
{{hardware:perenio:150099625-eaf92aac-b569-481a-af71-6837c124b5a5.png?200|}}
{{hardware:perenio:p1030079.jpg?200|}}
{{hardware:perenio:p1030078.jpg?200|}}



===== Additional collected info =====

<details>
<summary>Boot log</summary>
<code>
U-Boot 1.1.4.svn5120 (Jan 12 2018 - 13:20:07)

cus531mp3 - Honey Bee 2.0DRAM:  
sri
Honey Bee 2.0
ath_ddr_initial_config(195): (16bit) ddr2 init
ath_sys_frequency: cpu 650 ddr 597 ahb 216
tap = 0x00000003
Tap (low, high) = (0x8, 0x21)
Tap values = (0x14, 0x14, 0x14, 0x14)
64 MB
Top of RAM usable for U-Boot at: 84000000
Reserving 222k for U-Boot at: 83fc8000
Reserving 192k for malloc() at: 83f98000
Reserving 44 Bytes for Board Info at: 83f97fd4
Reserving 36 Bytes for Global Data at: 83f97fb0
Reserving 128k for boot params() at: 83f77fb0
Stack Pointer at: 83f77f98
Now running in RAM - U-Boot at: 83fc8000
Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x16
flash size 0MB, sector count = 8
Flash: 512 kB
Power up PLL with outdiv = 0 then switch to 3
*** Warning *** : PCIe WLAN Module not found !!!
In:    serial
Out:   serial
Err:   serial
Net:   ath_gmac_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
ath_gmac_enet_initialize: reset mask:c02200 
Honey Bee ---->S27 PHY*
S27 reg init
: cfg1 0x800c0000 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 4 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 4 :10
eth0 up
Honey Bee ---->  MAC 1 S27 PHY *
S27 reg init
ATHRS27: resetting s27
ATHRS27: s27 reset done
: cfg1 0x800c0000 cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs27_phy_setup ATHR_PHY_CONTROL 0 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 0 :10
athrs27_phy_setup ATHR_PHY_CONTROL 1 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 1 :10
athrs27_phy_setup ATHR_PHY_CONTROL 2 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 2 :10
athrs27_phy_setup ATHR_PHY_CONTROL 3 :1000
athrs27_phy_setup ATHR_PHY_SPEC_STAUS 3 :10
eth1 up
eth0, eth1
Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014  Qualcomm Atheros Inc.
====== NAND Parameters ======
sc = 0x83ff8b20 page = 0x800 block = 0x20000
Setting 0x181162c0 to 0x2851a100
Hit any key to stop autoboot:  0 

Loading from device 0: ath-spi-nand (offset 0x2200000)
   Image Name:   MIPS OpenWrt Linux-3.18.29
   Created:      2018-05-02   9:39:12 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1476171 Bytes =  1.4 MB
   Load Address: 80060000
   Entry Point:  80060000
## Booting image at 81000000 ...
   Image Name:   MIPS OpenWrt Linux-3.18.29
   Created:      2018-05-02   9:39:12 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1476171 Bytes =  1.4 MB
   Load Address: 80060000
   Entry Point:  80060000
   Verifying Checksum at 0x81000040 ...OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

[    0.000000] Linux version 3.18.29 (yangcanghua@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r6273) ) #50 Wed May 2 17:38:35 CST 2018
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[    0.000000] SoC: Qualcomm Atheros QCA9533 ver 2 rev 0
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x00000000-0x03ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x00000000-0x03ffffff]
[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line:  ubi.mtd=8 ubootsvn=5120 board=CUS531MP3-NAND console=ttyS0,115200 ubi.mtd=overlay rootfs=/dev/mtdblock:rootfs rootfstype=squashfs noinitrd init=/sbin/init bootslot=1 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(u-boot-env-bak),64k(reserved),64k(art);spi0.1:2m(kernel-0),32m(root-0),2m(kernel-1)ro,32m(root-1),60m(overlay),34m@0x2200000(firmware1) production=0000 hwversion=V2.0 app_switch=default mem=64M rootfstype=squashfs,jffs2 noinitrd
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 59916K/65536K available (3395K kernel code, 156K rwdata, 672K rodata, 184K init, 194K bss, 5620K reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:51
[    0.000000] Clocks: CPU:650.000MHz, DDR:597.241MHz, AHB:216.666MHz, Ref:25.000MHz
[    0.000000] Calibrating delay loop... 432.53 BogoMIPS (lpj=2162688)
[    0.060000] pid_max: default: 32768 minimum: 301
[    0.060000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070000] Performance counters: mips/24K PMU enabled, 2 32-bit counters available to each CPU, irq 13
[    0.080000] NET: Registered protocol family 16
[    0.090000] MIPS: machine is Qualcomm Atheros CUS531 MP3 nand reference board
[    0.090000] ar724x-pci ar724x-pci.0: PCIe link is down
[    0.100000] registering PCI controller with io_map_base unset
[    0.110000] ar71xx: invalid MDIO id 1
[    0.550000] i2c-gpio i2c-gpio.0: using pins 17 (SDA) and 16 (SCL)
[    0.560000] PCI host bridge to bus 0000:00
[    0.560000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff]
[    0.570000] pci_bus 0000:00: root bus resource [io  0x0000]
[    0.570000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.580000] Bluetooth: Core ver 2.19
[    0.580000] NET: Registered protocol family 31
[    0.580000] Bluetooth: HCI device and connection manager initialized
[    0.590000] Bluetooth: HCI socket layer initialized
[    0.590000] Bluetooth: L2CAP socket layer initialized
[    0.600000] Bluetooth: SCO socket layer initialized
[    0.600000] Switched to clocksource MIPS
[    0.610000] NET: Registered protocol family 2
[    0.610000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.610000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.620000] TCP: Hash tables configured (established 1024 bind 1024)
[    0.630000] TCP: reno registered
[    0.630000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.640000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.640000] NET: Registered protocol family 1
[    0.650000] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.660000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.670000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.680000] msgmni has been set to 117
[    0.690000] io scheduler noop registered
[    0.690000] io scheduler deadline registered (default)
[    0.700000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.700000] console [ttyS0] disabled
[    0.730000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 1562500) is a 16550A
[    0.740000] console [ttyS0] enabled
[    0.740000] console [ttyS0] enabled
[    0.740000] bootconsole [early0] disabled
[    0.740000] bootconsole [early0] disabled
[    0.750000] m25p80 spi0.0: found mx25l3205d, expected m25p80
[    0.760000] m25p80 spi0.0: mx25l3205d (4096 Kbytes)
[    0.760000] 5 cmdlinepart partitions found on MTD device spi0.0
[    0.770000] Creating 5 MTD partitions on "spi0.0":
[    0.780000] 0x000000000000-0x000000040000 : "u-boot"
[    0.780000] 0x000000040000-0x000000050000 : "u-boot-env"
[    0.790000] 0x000000050000-0x000000060000 : "u-boot-env-bak"
[    0.790000] 0x000000060000-0x000000070000 : "reserved"
[    0.800000] 0x000000070000-0x000000080000 : "art"
[    0.810000] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0x12
[    0.810000] nand: Macronix MX35LF1G4EAB 1G 3.3V 8-bit
[    0.820000] nand: 128MiB, SLC, page size: 2048, OOB size: 64
[    0.830000] nand: WARNING: spi0.1: the ECC used on your system is too weak compared to the one required by the NAND chip
[    0.840000] Scanning device for bad blocks
[    0.890000] Bad eraseblock 735 at 0x000005be0000
[    0.910000] 6 cmdlinepart partitions found on MTD device spi0.1
[    0.910000] Creating 6 MTD partitions on "spi0.1":
[    0.920000] 0x000000000000-0x000000200000 : "kernel-0"
[    0.930000] 0x000000200000-0x000002200000 : "root-0"
[    0.930000] 0x000002200000-0x000002400000 : "kernel-1"
[    0.940000] 0x000002400000-0x000004400000 : "root-1"
[    0.940000] 0x000004400000-0x000008000000 : "overlay"
[    0.950000] 0x000002200000-0x000004400000 : "firmware1"
[    0.990000] libphy: ag71xx_mdio: probed
[    1.580000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY]
[    1.590000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[    2.180000] ag71xx-mdio.1: Found an AR934X built-in switch
[    2.220000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[    2.230000] rtc-pcf8563 0-0051: chip found, driver version 0.4.3
[    2.240000] rtc (null): invalid alarm value: 2021-4-13 34:22:0
[    2.240000] rtc-pcf8563 0-0051: rtc core: registered rtc-pcf8563 as rtc0
[    2.250000] Bluetooth: HCI UART driver ver 2.2
[    2.260000] Bluetooth: HCI H4 protocol initialized
[    2.260000] Bluetooth: HCI BCSP protocol initialized
[    2.270000] Bluetooth: HCIATH3K protocol initialized
[    2.270000] TCP: cubic registered
[    2.280000] NET: Registered protocol family 10
[    2.280000] NET: Registered protocol family 17
[    2.290000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    2.300000] 8021q: 802.1Q VLAN Support v1.8
[    2.310000] UBI: attaching mtd8 to ubi0
[    2.800000] UBI: scanning is finished
[    2.830000] UBI: attached mtd8 (name "root-1", size 32 MiB) to ubi0
[    2.840000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.840000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.850000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.860000] UBI: good PEBs: 256, bad PEBs: 0, corrupted PEBs: 0
[    2.860000] UBI: user volume: 2, internal volumes: 1, max. volumes count: 128
[    2.870000] UBI: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 29864118
[    2.880000] UBI: available PEBs: 0, total reserved PEBs: 256, PEBs reserved for bad PEB handling: 20
[    2.890000] UBI: background thread "ubi_bgt0d" started, PID 332
[    2.900000] mtd: device 11 (rootfs) set to be root filesystem
[    2.900000] UBI: attaching mtd9 to ubi1
[    3.820000] UBI: scanning is finished
[    3.850000] UBI: attached mtd9 (name "overlay", size 60 MiB) to ubi1
[    3.860000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    3.860000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    3.870000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
[    3.880000] UBI: good PEBs: 479, bad PEBs: 1, corrupted PEBs: 0
[    3.890000] UBI: user volume: 0, internal volumes: 1, max. volumes count: 128
[    3.890000] UBI: max/mean erase counter: 1/1, WL threshold: 4096, image sequence number: 3988775088
[    3.900000] UBI: available PEBs: 456, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
[    3.910000] rtc-pcf8563 0-0051: setting system clock to 2021-03-31 17:47:17 UTC (1617212837)
[    3.920000] UBI: background thread "ubi_bgt1d" started, PID 350
[    3.940000] VFS: Mounted root (squashfs filesystem) readonly on device 31:11.
[    3.940000] Freeing unused kernel memory: 184K (80482000 - 804b0000)
[    4.810000] init: Console is alive
[    4.810000] init: - watchdog -
[    6.410000] usbcore: registered new interface driver usbfs
[    6.410000] usbcore: registered new interface driver hub
[    6.420000] usbcore: registered new device driver usb
[    6.430000] Button Hotplug driver version 0.4.1
[    6.440000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.450000] ehci-platform: EHCI generic platform driver
[    6.450000] ehci-platform ehci-platform: EHCI Host Controller
[    6.460000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[    6.470000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[    6.500000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[    6.500000] hub 1-0:1.0: USB hub found
[    6.510000] hub 1-0:1.0: 1 port detected
[    6.510000] uhci_hcd: USB Universal Host Controller Interface driver
[    6.830000] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    6.860000] init: - preinit -
[    7.260000] hub 1-1:1.0: USB hub found
[    7.270000] hub 1-1:1.0: 4 ports detected
[    7.720000] usb 1-1.2: new full-speed USB device number 3 using ehci-platform
[    7.730000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[    7.770000] random: mktemp urandom read with 13 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.910000] usb 1-1.4: new full-speed USB device number 4 using ehci-platform
[    8.000000] usb 1-1.4: device descriptor read/64, error -32
[    8.190000] usb 1-1.4: device descriptor read/64, error -32
[    8.380000] usb 1-1.4: new full-speed USB device number 5 using ehci-platform
[    8.470000] usb 1-1.4: device descriptor read/64, error -32
[    8.660000] usb 1-1.4: device descriptor read/64, error -32
[    8.850000] usb 1-1.4: new full-speed USB device number 6 using ehci-platform
[    9.280000] usb 1-1.4: device not accepting address 6, error -32
[    9.360000] usb 1-1.4: new full-speed USB device number 7 using ehci-platform
[    9.790000] usb 1-1.4: device not accepting address 7, error -32
[    9.790000] usb 1-1-port4: unable to enumerate USB device
Before mount_root
[   10.950000] mount_root: loading kmods from internal overlay
[   11.380000] block: attempting to load /etc/config/fstab
[   11.380000] block: unable to load configuration (fstab: Entry not found)
[   11.390000] block: no usable configuration
[   11.400000] jffs2: write-buffering enabled buffer (2048) erasesize (126976)
[   11.530000] jffs2: notice: (416) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   11.910000] block: attempting to load /etc/config/fstab
[   11.910000] block: unable to load configuration (fstab: Entry not found)
[   11.920000] block: no usable configuration
[   11.930000] mount_root: switching to jffs2 overlay
After mount_root
[   11.990000] procd: - early -
[   11.990000] procd: - watchdog -
[   12.760000] procd: - ubus -
[   13.780000] procd: - init -
Please press Enter to activate this console.
[   14.370000] jffs2: notice: (420) check_node_data: wrong data CRC in data node at 0x006ade94: read 0x3bd045b9, calculated 0x446b1e34.
[   15.240000] NET: Registered protocol family 8
[   15.240000] NET: Registered protocol family 20
[   15.280000] l2tp_core: L2TP core driver, V2.0
[   15.290000] l2tp_netlink: L2TP netlink interface
[   15.290000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[   15.300000] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[   15.310000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[   15.320000] gre: GRE over IPv4 demultiplexor driver
[   15.330000] ip_gre: GRE over IPv4 tunneling driver
[   15.350000] PPP generic driver version 2.4.2
[   15.380000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   15.410000] i2c /dev entries driver
[   15.430000] hidraw: raw HID events driver (C) Jiri Kosina
[   15.450000] u32 classifier
[   15.450000]     input device check on
[   15.450000]     Actions configured
[   15.460000] Mirror/redirect action on
[   15.470000] nf_conntrack version 0.5.0 (939 buckets, 3756 max)
[   15.490000] Loading modules backported from Linux version v3.18-116968-ga5cea28c4c2f
[   15.500000] Backport generated by backports.git backports-20160216-0-ge3c56e41
[   15.700000] ###################################################
[   15.700000] BTCOEX:Disabled
[   15.700000] 	priority_time:2
[   15.700000] 	first_slot_time:18
[   15.700000] 	wl_active_time:0
[   15.700000] 	wl_qc_time:0
[   15.700000] 	time_extend:10
[   15.700000] 	ack_cts:0
[   15.700000] 	btcoex_period:45
[   15.700000] 	btcoex_duty_cycle:40
[   15.730000] ###################################################
[   15.750000] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47
[   15.780000] ip_tables: (C) 2000-2006 Netfilter Core Team
[   15.820000] nf_conntrack_rtsp v0.6.21 loading
[   15.860000] nf_nat_rtsp v0.6.21 loading
[   15.880000] PPP MPPE Compression module registered
[   15.890000] NET: Registered protocol family 24
[   15.900000] PPTP driver version 0.8.5
[   15.920000] usbcore: registered new interface driver usbserial
[   15.930000] usbcore: registered new interface driver usbserial_generic
[   15.930000] usbserial: USB Serial support registered for generic
[   16.000000] xt_time: kernel timezone is -0000
[   16.010000] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[   16.040000] usbcore: registered new interface driver pl2303
[   16.050000] usbserial: USB Serial support registered for pl2303
[   16.060000] pl2303 1-1.2:1.0: pl2303 converter detected
[   16.060000] usb 1-1.2: pl2303 converter now attached to ttyUSB0
[   33.540000] device eth1 entered promiscuous mode
[   33.560000] br-lan: port 1(eth1) entered forwarding state
[   33.570000] br-lan: port 1(eth1) entered forwarding state
[   33.630000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   34.480000] br-lan: port 1(eth1) entered disabled state
[   36.760000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   39.090000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   47.640000] random: nonblocking pool is initialized
[   48.960000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   50.380000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[  427.450000] eth0: link up (100Mbps/Full duplex)
[  427.450000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready



BusyBox v1.23.2 (2021-09-13 20:40:24 UTC) built-in shell (ash)


                                                                              ,9&G3
                                                                          HHHHHXSXAHHHH5
                                                                        HHH:          GHH;
                                                                       HH5   HHHHHHH&   HHH
                                                                      XHr  HHHA   ,HHHH  HH
                                                                          HH         &HH
       .                                     .              .                   HG
 HH HHHHHHHG      AHHHHHHH     HH HHHH   3HHHHHHH     HHhHHHHHHH     HH      HrsHH HG
 HHH&     HHH    HHA    5HHS   HHHH3    HH&     HHH   HHHr    rHH    HH    HHA sHH sHH2
 HH;       SHH  HH        HH   HHA     HH&       HH.  HHS      HHS   HH   HH   ;HH   HH
 HH         HH  HHHHHHHHHHHH   HH      HHHHHHHHHHHHX  HH,      HH2   HH   HH         ,H3
 HH         HH  HH             HH      HHX            HH,      HH2   HH   HH         &H:
 HHH       HHi  9HH       G    HH       HH       i:   HH,      HH2   HH    HH        HH
 HHAHHHHHHHH      HHHHHHHHH    HH        HHHHHHHHH9   HH,      HH2   HH     GHHHHHHHH
 HH   hHG;          5HHA;      sr          ;AHH5      ,i       .i    ii        iX5;
 HH
 HH




 ---------------------------------------------------------------
   Preview version 1.0.3X  Perenio 2018 © ... (Gateway PEACG01 )
 ---------------------------------------------------------------
</code>
</details>

<details>
<summary>u-boot env</summary>
<code>ath> printenv 
bootargs=board=CUS531MP3-NAND console=ttyS0,115200  ubi.mtd=5,2048 root=/dev/mtdblock8 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),128k(reserved),64k(art);spi0.1:2m(kernel),36m(rootfs),90m(data),38m@0x0(firmware) rootfstype=squashfs,jffs2 noinitrd
bootcmd=if test ${bootslot} -ne 1;then run boot_from_slot_0;else run boot_from_slot_1;fi
bootdelay=2
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
ipaddr=192.168.1.2
serverip=192.168.1.10
app_switch=default
kernel_0_start=0x0
root_0_start=0x400000
mtdparts0=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(u-boot-env-bak),64k(reserved),64k(art);spi0.1:2m(kernel-0)ro,32m(root-0),2m(kernel-1),32m(root-1),60m(overlay),34m@0x0(firmware0)
boot_from_slot_0=setenv bootargs ubi.mtd=6 ubootsvn=${ubootsvn}  ${std_bootargs0} mtdparts=${mtdparts0} production=${production} hwversion=${hwversion} app_switch=${app_switch}; nboot 0x81000000 0 ${kernel_0_start}
kernel_1_start=0x2200000
root_1_start=0x2600000
mtdparts1=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(u-boot-env-bak),64k(reserved),64k(art);spi0.1:2m(kernel-0),32m(root-0),2m(kernel-1)ro,32m(root-1),60m(overlay),34m@0x2200000(firmware1)
boot_from_slot_1=setenv bootargs ubi.mtd=8 ubootsvn=${ubootsvn}  ${std_bootargs1} mtdparts=${mtdparts1} production=${production} hwversion=${hwversion}  app_switch=${app_switch}; nboot 0x81000000 0 ${kernel_1_start}
std_bootargs0=board=CUS531MP3-NAND console=ttyS0,115200 ubi.mtd=overlay rootfs=/dev/mtdblock:rootfs  rootfstype=squashfs noinitrd init=/sbin/init  bootslot=0
std_bootargs1=board=CUS531MP3-NAND console=ttyS0,115200 ubi.mtd=overlay rootfs=/dev/mtdblock:rootfs  rootfstype=squashfs noinitrd init=/sbin/init  bootslot=1
production=0000
sysreset=0
bootKernelFailCount=0
flash_uboot=tftp 0x80060000 u-boot.bin&&erase 0x9f000000 +$filesize&&cp.b $fileaddr 0x9f000000 $filesize
flash_kernel-0=tftp 0x80060000 kernel.bin&&nand erase 0x0 0x200000&&nand write $fileaddr 0x0 $filesize
flash_root-0=tftp 0x80060000   root.bin&&nand erase 0x200000 0x2000000&&nand write  $fileaddr 0x200000 $filesize
flash_kernel-1=tftp 0x80060000 kernel.bin&&nand erase 0x2200000 0x200000&&nand write $fileaddr 0x2200000 $filesize
flash_root-1=tftp 0x80060000  root.bin&&nand erase 0x2400000 0x2000000&&nand write $fileaddr 0x2400000 $filesize
overy_start=0x4400000
erase_overlay=nand erase 0x4400000 0x3C00000
flash_firmware=run flash_uboot;run flash_kernel-0;run flash_root-0;run flash_kernel-1;run flash_root-1;run erase_overlay
store_factory_env=erase 0x9f050000  +0x10000;cp.b  0x9f040000  0x80060000 0x10000;cp.b 0x80060000  0x9f050000 0x10000
restore_factory_env=erase 0x9f040000  +0x10000;cp.b  0x9f050000  0x80060000 0x10000;cp.b 0x80060000  0x9f040000 0x10000
ethact=eth0
DevType=1
customer=Perenio
hwversion=V2.0
UUID=0a098d9e-8cff-48de-8dbf-e0b9aa905bd2
PIN=61589273
SN=3D67177F9D8C1A1
model_id=PEACG01_Ihvg
model_key=IMK5wrXC
uboot_env_init=1
mode=ldsGateReleaseMode
model=PEACG01
bootslot=1
fw_new_version=0.1.44
fw_version=0.1.44
ncp_version=6.6.3
camera_provisioned=false
wireless_enabled=true
wireless_mode=ap
ethernet_enabled=true
stdin=serial
stdout=serial
stderr=serial
ubootsvn=5120

Environment size: 3130/65532 bytes
</code>
</details>


<details>
<summary>netstat</summary>
<code>root@OpenWrt:/# netstat 
Active Internet connections (w/o servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State       
tcp        0      0 localhost:44987         localhost:1883          ESTABLISHED 
tcp        0      0 localhost:1883          localhost:44986         ESTABLISHED 
tcp        0      0 localhost:44986         localhost:1883          ESTABLISHED 
tcp        0      0 localhost:1883          localhost:44987         ESTABLISHED 
udp        0      0 172.16.0.143:ntp        107-194-210-155.lightspeed.lsvlky.sbcglobal.net:ntp ESTABLISHED 
Active UNIX domain sockets (w/o servers)
Proto RefCnt Flags       Type       State         I-Node Path
unix  9      [ ]         DGRAM                      1939 /dev/log
unix  2      [ ]         DGRAM                      4821 /var/run/hostapd/wlan0
unix  2      [ ]         DGRAM                      7580 
unix  2      [ ]         DGRAM                      5759 
unix  3      [ ]         STREAM     CONNECTED       1934 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1933 
unix  3      [ ]         STREAM     CONNECTED       5595 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1944 
unix  3      [ ]         STREAM     CONNECTED       5594 
unix  3      [ ]         STREAM     CONNECTED       1978 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1977 
unix  3      [ ]         STREAM     CONNECTED       2177 
unix  3      [ ]         STREAM     CONNECTED        516 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED        515 
unix  3      [ ]         STREAM     CONNECTED       2178 /var/run/ubus.sock
unix  2      [ ]         DGRAM                      2936 
unix  3      [ ]         STREAM     CONNECTED       1945 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       3760 /var/run/ubus.sock
unix  2      [ ]         DGRAM                      4378 
unix  3      [ ]         STREAM     CONNECTED       3759 
unix  2      [ ]         DGRAM                      4971 
unix  2      [ ]         DGRAM                      2262 
unix  2      [ ]         DGRAM                      2328 
unix  3      [ ]         STREAM     CONNECTED       4823 
unix  2      [ ]         DGRAM                      2919 
unix  3      [ ]         STREAM     CONNECTED       4824 /var/run/ubus.sock

root@OpenWrt:/# netstat -n -a
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address           Foreign Address         State       
tcp        0      0 0.0.0.0:8080            0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:80              0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:53              0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN      
tcp        0      0 0.0.0.0:1883            0.0.0.0:*               LISTEN      
tcp        0      0 127.0.0.1:44987         127.0.0.1:1883          ESTABLISHED 
tcp        0      0 127.0.0.1:1883          127.0.0.1:44986         ESTABLISHED 
tcp        0      0 127.0.0.1:44986         127.0.0.1:1883          ESTABLISHED 
tcp        0      0 127.0.0.1:1883          127.0.0.1:44987         ESTABLISHED 
tcp        0      0 :::5000                 :::*                    LISTEN      
tcp        0      0 :::80                   :::*                    LISTEN      
tcp        0      0 :::53                   :::*                    LISTEN      
tcp        0      0 :::22                   :::*                    LISTEN      
tcp        0      0 :::23                   :::*                    LISTEN      
tcp        0      0 :::1883                 :::*                    LISTEN      
udp        0      0 0.0.0.0:53              0.0.0.0:*                           
udp        0      0 0.0.0.0:67              0.0.0.0:*                           
udp        0      0 0.0.0.0:1900            0.0.0.0:*                           
udp        0      0 172.16.0.143:123        107.194.210.155:123     ESTABLISHED 
udp        0      0 192.168.1.2:37521       0.0.0.0:*                           
udp        0      0 192.168.1.2:5351        0.0.0.0:*                           
udp        0      0 :::546                  :::*                                
udp        0      0 :::53                   :::*                                
udp        0      0 :::5351                 :::*                                
raw        0      0 :::58                   :::*                    58          
Active UNIX domain sockets (servers and established)
Proto RefCnt Flags       Type       State         I-Node Path
unix  2      [ ACC ]     STREAM     LISTENING        513 /var/run/ubus.sock
unix  2      [ ACC ]     STREAM     LISTENING       5756 /var/run/bird.ctl
unix  9      [ ]         DGRAM                      1939 /dev/log
unix  2      [ ]         DGRAM                      4821 /var/run/hostapd/wlan0
unix  2      [ ]         DGRAM                      7580 
unix  2      [ ]         DGRAM                      5759 
unix  3      [ ]         STREAM     CONNECTED       1934 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1933 
unix  3      [ ]         STREAM     CONNECTED       5595 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1944 
unix  3      [ ]         STREAM     CONNECTED       5594 
unix  3      [ ]         STREAM     CONNECTED       1978 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       1977 
unix  3      [ ]         STREAM     CONNECTED       2177 
unix  3      [ ]         STREAM     CONNECTED        516 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED        515 
unix  3      [ ]         STREAM     CONNECTED       2178 /var/run/ubus.sock
unix  2      [ ]         DGRAM                      2936 
unix  3      [ ]         STREAM     CONNECTED       1945 /var/run/ubus.sock
unix  3      [ ]         STREAM     CONNECTED       3760 /var/run/ubus.sock
unix  2      [ ]         DGRAM                      4378 
unix  3      [ ]         STREAM     CONNECTED       3759 
unix  2      [ ]         DGRAM                      4971 
unix  2      [ ]         DGRAM                      2262 
unix  2      [ ]         DGRAM                      2328 
unix  3      [ ]         STREAM     CONNECTED       4823 
unix  2      [ ]         DGRAM                      2919 
unix  3      [ ]         STREAM     CONNECTED       4824 /var/run/ubus.sock
</code>
</details>


<details>
<summary>opkg list-installed</summary>
<code>root@OpenWrt:/# opkg list-installed
alsa-lib - 1.0.28-1
ath10k-firmware - g18118da-1
base-files - 157.2-unknown
bird4 - 1.4.5-2
bird4-uci - 0.2
block-mount - 2016-01-10-96415afecef35766332067f4205ef3b2c7561d21
busybox - 1.23.2-1
curl - 7.40.0-3.2
dnsmasq-dhcpv6 - 2.73-1
dropbear - 2015.67-1
ethtool - 3.18-1
firewall - 2015-07-27
fstools - 2016-01-10-96415afecef35766332067f4205ef3b2c7561d21
gdb - 7.8-2
gdbserver - 7.8-2
glib2 - 2.44.1-1
hostapd - 2015-09-27-1
hostapd-common - 2015-09-27-1
hostapd-utils - 2015-09-27-1
i2c-tools - 3.1.2-1
ip - 4.0.0-1
ip6tables - 1.4.21-1
iperf - 2.0.5-1
iptables - 1.4.21-1
iptables-mod-conntrack-extra - 1.4.21-1
iptables-mod-ipopt - 1.4.21-1
iw - 4.3-1
iwinfo - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371
jshn - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb
jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9
kaa-camera-service - v2.2.18
kernel - 3.18.29-1-8ea585a6b5a768c445ceb8254de2ca34
kmod-art2 - 3.18.29+CS10.2v4.9.432-1
kmod-ath - 3.18.29+20160607-1
kmod-ath9k - 3.18.29+20160607-1
kmod-ath9k-common - 3.18.29+20160607-1
kmod-atm - 3.18.29-1
kmod-button-hotplug - 3.18.29-3
kmod-cfg80211 - 3.18.29+20160607-1
kmod-crypto-aead - 3.18.29-1
kmod-crypto-aes - 3.18.29-1
kmod-crypto-arc4 - 3.18.29-1
kmod-crypto-core - 3.18.29-1
kmod-crypto-ecb - 3.18.29-1
kmod-crypto-hash - 3.18.29-1
kmod-crypto-manager - 3.18.29-1
kmod-crypto-pcompress - 3.18.29-1
kmod-crypto-sha1 - 3.18.29-1
kmod-gpio-button-hotplug - 3.18.29-1
kmod-gpio-dev - 3.18.29-1
kmod-gre - 3.18.29-1
kmod-hid - 3.18.29-1
kmod-i2c-algo-bit - 3.18.29-1
kmod-i2c-core - 3.18.29-1
kmod-i2c-gpio - 3.18.29-1
kmod-i2c-gpio-custom - 3.18.29-2
kmod-ifb - 3.18.29-1
kmod-input-core - 3.18.29-1
kmod-input-evdev - 3.18.29-1
kmod-ip6tables - 3.18.29-1
kmod-ipt-conntrack - 3.18.29-1
kmod-ipt-conntrack-extra - 3.18.29-1
kmod-ipt-core - 3.18.29-1
kmod-ipt-ipopt - 3.18.29-1
kmod-ipt-nat - 3.18.29-1
kmod-ipt-nathelper-rtsp - 3.18.29+2.10-1
kmod-iptunnel - 3.18.29-1
kmod-l2tp - 3.18.29-1
kmod-l2tp-eth - 3.18.29-1
kmod-l2tp-ip - 3.18.29-1
kmod-lib-crc-ccitt - 3.18.29-1
kmod-lib-crc16 - 3.18.29-1
kmod-lib-textsearch - 3.18.29-1
kmod-mac80211 - 3.18.29+20160607-1
kmod-mppe - 3.18.29-1
kmod-nf-conntrack - 3.18.29-1
kmod-nf-conntrack6 - 3.18.29-1
kmod-nf-ipt - 3.18.29-1
kmod-nf-ipt6 - 3.18.29-1
kmod-nf-nat - 3.18.29-1
kmod-nf-nathelper - 3.18.29-1
kmod-nf-nathelper-extra - 3.18.29-1
kmod-nls-base - 3.18.29-1
kmod-nls-koi8r - 3.18.29-1
kmod-nls-utf8 - 3.18.29-1
kmod-ppp - 3.18.29-1
kmod-pppoa - 3.18.29-1
kmod-pppoe - 3.18.29-1
kmod-pppol2tp - 3.18.29-1
kmod-pppox - 3.18.29-1
kmod-pptp - 3.18.29-1
kmod-sched-connmark - 3.18.29-1
kmod-sched-core - 3.18.29-1
kmod-slhc - 3.18.29-1
kmod-sound-core - 3.18.29-1
kmod-udptunnel4 - 3.18.29-1
kmod-udptunnel6 - 3.18.29-1
kmod-usb-core - 3.18.29-1
kmod-usb-serial - 3.18.29-1
kmod-usb-serial-pl2303 - 3.18.29-1
kmod-usb-uhci - 3.18.29-1
kmod-usb2 - 3.18.29-1
libattr - 20150220-1
libblobmsg-json - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb
libbz2 - 1.0.6-2
libc - 1.0.14-1
libcap - 2.24-1
libcares - 1.10.0-1
libcurl - 7.40.0-3.2
libdb47 - 4.7.25.4.NC-4.1
libdbus - 1.9.14-1
libexpat - 2.1.0-3
libffi - 3.0.13-1
libgcc - 4.8-linaro-1
libgdbm - 1.11-1
libgmp - 6.0.0-1
libical - 1.0-1
libip4tc - 1.4.21-1
libip6tc - 1.4.21-1
libiwinfo - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371
libiwinfo-lua - 2015-06-01-ade8b1b299cbd5748db1acf80dd3e9f567938371
libjson-c - 0.12-1
libjson-script - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb
liblua - 5.1.5-1
liblxc - 1.1.3-1
liblzma - 5.2.1-2
liblzo - 2.08-1
libmagic - 5.25-1
libmosquitto - 1.4.8-1
libmysqlclient - 5.1.73-1
libncurses - 5.9-2
libnl - 3.2.21-1
libnl-tiny - 0.1-4
libopenssl - 1.0.2h-1
libpam - 1.1.8-4
libpcap - 1.5.3-1
libpolarssl - 1.3.15-1
libpthread - 1.0.14-1
libreadline - 6.3-1
librpc - 2015-11-04-a921e3ded051746f9f7cd5e5a312fb6771716aac
librt - 1.0.14-1
libsqlite3 - 3081101-1
libstdcpp - 4.8-linaro-1
libthread-db - 1.0.14-1
libubox - 2015-11-08-10429bccd0dc5d204635e110a7a8fae7b80d16cb
libubus - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
libubus-lua - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
libuci - 2015-08-27.1-1
libuci-lua - 2015-08-27.1-1
libusb-1.0 - 1.0.19-1
libuuid - 2.25.2-4
libwebsockets-openssl - 1.3-chrome37-firefox30-1
libxml2 - 2.9.2-3
libxtables - 1.4.21-1
libyaml - 0.1.6-1
linux-atm - 2.5.2-5
logd - 2015-11-22-c086167a0154745c677f8730a336ea9cf7d71031
lua - 5.1.5-1
lxc - 1.1.3-1
lxc-common - 1.1.3-1
lxc-configs - 1.1.3-1
lxc-create - 1.1.3-1
lxc-hooks - 1.1.3-1
lxc-templates - 1.1.3-1
miniupnpd - 1.9.20150609-1
mosquitto - 1.4.8-1
mosquitto-client - 1.4.8-1
mtd - 24
nano - 2.5.3-1
netifd - 2015-12-16-245527193e90906451be35c2b8e972b8712ea6ab
ntpclient - 2010_365-1
odhcp6c - 2015-07-29-dc186d6d2b0dd4ad23ca5fc69c00e81f796ff6d9
odhcpd - 2015-11-19-01d3f9d64486ac1daa144848944e877e7f0cb762
openssh-keygen - 7.1p2-1
openssh-server-pam - 7.1p2-1
openssh-sftp-server - 7.1p2-1
openssl-util - 1.0.2h-1
opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-9
opkg-smime - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-9
ppp - 2.4.7-6
ppp-mod-pppoa - 2.4.7-6
ppp-mod-pppoe - 2.4.7-6
ppp-mod-pppol2tp - 2.4.7-6
ppp-mod-pptp - 2.4.7-6
ppp-mod-radius - 2.4.7-6
ppp-multilink - 2.4.7-6
pppdump - 2.4.7-6
pppstats - 2.4.7-6
procd - 2015-10-29.1-d5fddd91b966424bb63e943e789704d52382cc18
python - 2.7.13-1
python-base - 2.7.13-1
python-codecs - 2.7.13-1
python-compiler - 2.7.13-1
python-ctypes - 2.7.13-1
python-db - 2.7.13-1
python-decimal - 2.7.13-1
python-distutils - 2.7.13-1
python-email - 2.7.13-1
python-gdbm - 2.7.13-1
python-light - 2.7.13-1
python-logging - 2.7.13-1
python-multiprocessing - 2.7.13-1
python-mysql - 1.2.5-1
python-ncurses - 2.7.13-1
python-openssl - 2.7.13-1
python-pip - 1.5.6-1
python-pydoc - 2.7.13-1
python-pyserial - 2.7-1
python-setuptools - 7.0-1
python-smbus - 3.1.2-1
python-sqlite3 - 2.7.13-1
python-unittest - 2.7.13-1
python-xml - 2.7.13-1
python-xmodem - 0.4.5-1
python-yaml - 3.11-1
python3-base - 3.4.3-2
python3-light - 3.4.3-2
qca-legacy-uboot-cus531mp3-nand - g18118da-1
qos-scripts - 1.2.1-7
resolveip - 2
rp-pppoe-relay - 3.11-1
rpcd - 2016-04-13-73aea9b8b621a1ce034bc6ee00c9d058a40c8a3d
rpcd-mod-lxc - 20141012
simplejson - 3.6.5-1
sqlite3-cli - 3081101-1
sudo - 1.8.14p3-1
sysstat - 11.0.4-2
tc - 4.0.0-1
tcpdump - 4.5.1-4
terminfo - 5.9-2
uboot-envtools - 2014.10-2
ubox - 2015-11-22-c086167a0154745c677f8730a336ea9cf7d71031
ubus - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
ubusd - 2015-05-25-f361bfa5fcb2daadf3b160583ce665024f8d108e
uci - 2015-08-27.1-1
uclibcxx - 0.2.4-1
uhttpd - 2015-11-08-fe01ef3f52adae9da38ef47926cd50974af5d6b7
uhttpd-mod-ubus - 2015-11-08-fe01ef3f52adae9da38ef47926cd50974af5d6b7
usbutils - 007-1
usign - 2015-05-08-cf8dcdb8a4e874c77f3e9a8e9b643e8c17b19131
wireless-tools - 29-5
wpa-cli - 2015-09-27-1
wpa-supplicant-p2p - 2015-09-27-1
zlib - 1.2.8-1
zoneinfo-europe - 2015d-1
</code>
</details>


<details>
<summary>/proc/mtd</summary>
<code>root@OpenWrt:/# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00040000 00010000 "u-boot"
mtd1: 00010000 00010000 "u-boot-env"
mtd2: 00010000 00010000 "u-boot-env-bak"
mtd3: 00010000 00010000 "reserved"
mtd4: 00010000 00010000 "art"
mtd5: 00200000 00020000 "kernel-0"
mtd6: 02000000 00020000 "root-0"
mtd7: 00200000 00020000 "kernel-1"
mtd8: 02000000 00020000 "root-1"
mtd9: 03c00000 00020000 "overlay"
mtd10: 02200000 00020000 "firmware1"
mtd11: 0141a000 0001f000 "rootfs"
mtd12: 007fe000 0001f000 "rootfs_data"
</code>
</details>


<details>
<summary>/proc/cmdline</summary>
<code>root@OpenWrt:/# cat /proc/cmdline
 ubi.mtd=8 ubootsvn=5120 board=CUS531MP3-NAND console=ttyS0,115200 ubi.mtd=overlay rootfs=/dev/mtdblock:rootfs rootfstype=squashfs noinitrd init=/sbin/init bootslot=1 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(u-boot-env-bak),64k(reserved),64k(art);spi0.1:2m(kernel-0),32m(root-0),2m(kernel-1)ro,32m(root-1),60m(overlay),34m@0x2200000(firmware1) production=0000 hwversion=V2.0 app_switch=default mem=64M rootfstype=squashfs,jffs2 noinitrd
</code>
</details>


<details>
<summary>/sys/kernel/debug/gpio</summary>
<code>root@OpenWrt:/# cat /sys/kernel/debug/gpio
GPIOs 0-17, ath79:
 gpio-3   (cus531:gpio3:reset  ) out hi    
 gpio-4   (WPS button          ) in  lo    
 gpio-12  (cus531:green:power  ) out lo    
 gpio-13  (cus531:green:wan    ) out hi    
 gpio-14  (cus531:green:lan    ) out hi    
 gpio-15  (RESET button        ) in  lo    
 gpio-16  (scl                 ) in  hi    
 gpio-17  (sda                 ) in  hi    
</code>
</details>


<details>
<summary>uci show</summary>
<code>bird4.bird=bird
bird4.bird.use_UCI_config='1'
bird4.bird.UCI_config_file='/tmp/bird4.conf'
bird4.global=global
bird4.global.log_file='/tmp/bird4.log'
bird4.global.log='all'
bird4.global.debug='off'
bird4.global.router_id='172.16.1.6'
bird4.@table[0]=table
bird4.@table[0].name='aux'
bird4.kernel1=kernel
bird4.kernel1.table='aux'
bird4.kernel1.import='all'
bird4.kernel1.export='all'
bird4.kernel1.kernel_table='100'
bird4.kernel1.scan_time='10'
bird4.kernel1.learn='1'
bird4.kernel1.persist='0'
bird4.kernel1.disabled='0'
bird4.device1=device
bird4.device1.scan_time='10'
bird4.device1.disabled='0'
bird4.static1=static
bird4.static1.table='aux'
bird4.static1.disabled='0'
bird4.bgp1=bgp
bird4.bgp1.template='bgp_common'
bird4.bgp1.description='Description of the BGP instance'
bird4.bgp1.neighbor_address='172.16.1.5'
bird4.bgp1.neighbor_as='65530'
bird4.bgp1.source_address='172.16.1.6'
bird4.bgp1.next_hop_self='0'
bird4.bgp1.next_hop_keep='0'
bird4.bgp1.rr_client='1'
bird4.bgp1.rr_cluster_id='172.16.1.6'
bird4.bgp_common=bgp_template
bird4.bgp_common.table='aux'
bird4.bgp_common.import='all'
bird4.bgp_common.export='all'
bird4.bgp_common.local_address='172.16.1.6'
bird4.bgp_common.local_as='65001'
bird4.bgp_common.import_limit='100'
bird4.bgp_common.import_limit_action='warn'
bird4.bgp_common.export_limit='100'
bird4.bgp_common.export_limit_action='warn'
bird4.bgp_common.receive_limit='100'
bird4.bgp_common.receive_limit_action='warn'
bird4.bgp_common.disabled='0'
bird4.@route[0]=route
bird4.@route[0].instance='static1'
bird4.@route[0].type='router'
bird4.@route[0].prefix='192.168.9.0/24'
bird4.@route[0].via='10.99.105.159'
dhcp.@dnsmasq[0]=dnsmasq
dhcp.@dnsmasq[0].domainneeded='1'
dhcp.@dnsmasq[0].boguspriv='1'
dhcp.@dnsmasq[0].filterwin2k='0'
dhcp.@dnsmasq[0].localise_queries='1'
dhcp.@dnsmasq[0].local='/lan/'
dhcp.@dnsmasq[0].domain='lan'
dhcp.@dnsmasq[0].expandhosts='1'
dhcp.@dnsmasq[0].nonegcache='0'
dhcp.@dnsmasq[0].authoritative='1'
dhcp.@dnsmasq[0].readethers='1'
dhcp.@dnsmasq[0].leasefile='/tmp/dhcp.leases'
dhcp.@dnsmasq[0].resolvfile='/tmp/resolv.conf.auto'
dhcp.lan=dhcp
dhcp.lan.interface='lan'
dhcp.lan.start='100'
dhcp.lan.limit='150'
dhcp.lan.leasetime='12h'
dhcp.lan.dhcpv6='server'
dhcp.lan.ra='server'
dhcp.wan=dhcp
dhcp.wan.interface='wan'
dhcp.wan.ignore='1'
dhcp.odhcpd=odhcpd
dhcp.odhcpd.maindhcp='0'
dhcp.odhcpd.leasefile='/tmp/hosts/odhcpd'
dhcp.odhcpd.leasetrigger='/usr/sbin/odhcpd-update'
dhcp.ap=dhcp
dhcp.ap.interface='ap'
dhcp.ap.start='100'
dhcp.ap.limit='150'
dhcp.ap.leasetime='12h'
dhcp.ap.dhcpv6='server'
dhcp.ap.ra='server'
dropbear.@dropbear[0]=dropbear
dropbear.@dropbear[0].PasswordAuth='on'
dropbear.@dropbear[0].RootPasswordAuth='on'
dropbear.@dropbear[0].Port='22'
firewall.@defaults[0]=defaults
firewall.@defaults[0].syn_flood='1'
firewall.@defaults[0].input='ACCEPT'
firewall.@defaults[0].output='ACCEPT'
firewall.@defaults[0].forward='REJECT'
firewall.@defaults[0].disabled='0'
firewall.@zone[0]=zone
firewall.@zone[0].name='lan'
firewall.@zone[0].network='lan'
firewall.@zone[0].input='ACCEPT'
firewall.@zone[0].output='ACCEPT'
firewall.@zone[0].forward='ACCEPT'
firewall.@zone[1]=zone
firewall.@zone[1].name='wan'
firewall.@zone[1].network='wan' 'wan6'
firewall.@zone[1].input='REJECT'
firewall.@zone[1].output='ACCEPT'
firewall.@zone[1].forward='REJECT'
firewall.@zone[1].masq='1'
firewall.@zone[1].mtu_fix='1'
firewall.@forwarding[0]=forwarding
firewall.@forwarding[0].src='lan'
firewall.@forwarding[0].dest='wan'
firewall.@rule[0]=rule
firewall.@rule[0].name='Allow-DHCP-Renew'
firewall.@rule[0].src='wan'
firewall.@rule[0].proto='udp'
firewall.@rule[0].dest_port='68'
firewall.@rule[0].target='ACCEPT'
firewall.@rule[0].family='ipv4'
firewall.@rule[1]=rule
firewall.@rule[1].name='Allow-Ping'
firewall.@rule[1].src='wan'
firewall.@rule[1].proto='icmp'
firewall.@rule[1].icmp_type='echo-request'
firewall.@rule[1].family='ipv4'
firewall.@rule[1].target='ACCEPT'
firewall.@rule[2]=rule
firewall.@rule[2].name='Allow-IGMP'
firewall.@rule[2].src='wan'
firewall.@rule[2].proto='igmp'
firewall.@rule[2].family='ipv4'
firewall.@rule[2].target='ACCEPT'
firewall.@rule[3]=rule
firewall.@rule[3].name='Allow-DHCPv6'
firewall.@rule[3].src='wan'
firewall.@rule[3].proto='udp'
firewall.@rule[3].src_ip='fe80::/10'
firewall.@rule[3].src_port='547'
firewall.@rule[3].dest_ip='fe80::/10'
firewall.@rule[3].dest_port='546'
firewall.@rule[3].family='ipv6'
firewall.@rule[3].target='ACCEPT'
firewall.@rule[4]=rule
firewall.@rule[4].name='Allow-MLD'
firewall.@rule[4].src='wan'
firewall.@rule[4].proto='icmp'
firewall.@rule[4].src_ip='fe80::/10'
firewall.@rule[4].icmp_type='130/0' '131/0' '132/0' '143/0'
firewall.@rule[4].family='ipv6'
firewall.@rule[4].target='ACCEPT'
firewall.@rule[5]=rule
firewall.@rule[5].name='Allow-ICMPv6-Input'
firewall.@rule[5].src='wan'
firewall.@rule[5].proto='icmp'
firewall.@rule[5].icmp_type='echo-request' 'echo-reply' 'destination-unreachable' 'packet-too-big' 'time-exceeded' 'bad-header' 'unknown-header-type' 'router-solicitation' 'neighbour-solicitation' 'router-advertisement' 'neighbour-advertisement'
firewall.@rule[5].limit='1000/sec'
firewall.@rule[5].family='ipv6'
firewall.@rule[5].target='ACCEPT'
firewall.@rule[6]=rule
firewall.@rule[6].name='Allow-ICMPv6-Forward'
firewall.@rule[6].src='wan'
firewall.@rule[6].dest='*'
firewall.@rule[6].proto='icmp'
firewall.@rule[6].icmp_type='echo-request' 'echo-reply' 'destination-unreachable' 'packet-too-big' 'time-exceeded' 'bad-header' 'unknown-header-type'
firewall.@rule[6].limit='1000/sec'
firewall.@rule[6].family='ipv6'
firewall.@rule[6].target='ACCEPT'
firewall.@include[0]=include
firewall.@include[0].path='/etc/firewall.user'
firewall.@rule[7]=rule
firewall.@rule[7].src='wan'
firewall.@rule[7].dest='lan'
firewall.@rule[7].proto='esp'
firewall.@rule[7].target='ACCEPT'
firewall.@rule[8]=rule
firewall.@rule[8].src='wan'
firewall.@rule[8].dest='lan'
firewall.@rule[8].dest_port='500'
firewall.@rule[8].proto='udp'
firewall.@rule[8].target='ACCEPT'
firewall.miniupnpd=include
firewall.miniupnpd.type='script'
firewall.miniupnpd.path='/usr/share/miniupnpd/firewall.include'
firewall.miniupnpd.family='any'
firewall.miniupnpd.reload='1'
fstab.@global[0]=global
fstab.@global[0].anon_swap='0'
fstab.@global[0].anon_mount='0'
fstab.@global[0].auto_swap='1'
fstab.@global[0].auto_mount='1'
fstab.@global[0].delay_root='5'
fstab.@global[0].check_fs='0'
network.loopback=interface
network.loopback.ifname='lo'
network.loopback.proto='static'
network.loopback.ipaddr='127.0.0.1'
network.loopback.netmask='255.0.0.0'
network.globals=globals
network.globals.ula_prefix='fde8:b21d:ea1a::/48'
network.lan=interface
network.lan.force_link='1'
network.lan.type='bridge'
network.lan.proto='static'
network.lan.ipaddr='192.168.1.2'
network.lan.netmask='255.255.255.0'
network.lan.gateway='192.168.1.2'
network.lan._orig_ifname='eth0'
network.lan._orig_bridge='true'
network.lan.metric='60'
network.lan.ifname='eth1'
network.wan=interface
network.wan.proto='dhcp'
network.wan.metric='20'
network.wan.ifname='eth0'
network.wan6=interface
network.wan6.proto='dhcpv6'
network.wan6.ifname='eth0'
network.@switch[0]=switch
network.@switch[0].name='switch0'
network.@switch[0].reset='1'
network.@switch[0].enable_vlan='1'
network.@switch_vlan[0]=switch_vlan
network.@switch_vlan[0].device='switch0'
network.@switch_vlan[0].vlan='1'
network.@switch_vlan[0].ports='0 1 2 3 4'
network.ap=interface
network.ap.proto='static'
network.ap.ipaddr='10.0.0.1'
network.ap.netmask='255.255.255.0'
network.sta=interface
network.sta.metric='40'
network.sta.proto='dhcp'
ntpclient.@ntpserver[0]=ntpserver
ntpclient.@ntpserver[0].hostname='0.openwrt.pool.ntp.org'
ntpclient.@ntpserver[0].port='123'
ntpclient.@ntpserver[1]=ntpserver
ntpclient.@ntpserver[1].hostname='1.openwrt.pool.ntp.org'
ntpclient.@ntpserver[1].port='123'
ntpclient.@ntpserver[2]=ntpserver
ntpclient.@ntpserver[2].hostname='2.openwrt.pool.ntp.org'
ntpclient.@ntpserver[2].port='123'
ntpclient.@ntpserver[3]=ntpserver
ntpclient.@ntpserver[3].hostname='3.openwrt.pool.ntp.org'
ntpclient.@ntpserver[3].port='123'
ntpclient.@ntpdrift[0]=ntpdrift
ntpclient.@ntpdrift[0].freq='0'
ntpclient.@ntpclient[0]=ntpclient
ntpclient.@ntpclient[0].interval='600'
pppoe.relay=pppoe_relay
pppoe.relay.enable='0'
pppoe.relay.client='lan'
pppoe.relay.server='wan'
qos.wan=interface
qos.wan.classgroup='Default'
qos.wan.enabled='0'
qos.wan.upload='128'
qos.wan.download='1024'
qos.@classify[0]=classify
qos.@classify[0].target='Priority'
qos.@classify[0].ports='22,53'
qos.@classify[0].comment='ssh, dns'
qos.@classify[1]=classify
qos.@classify[1].target='Normal'
qos.@classify[1].proto='tcp'
qos.@classify[1].ports='20,21,25,80,110,443,993,995'
qos.@classify[1].comment='ftp, smtp, http(s), imap'
qos.@classify[2]=classify
qos.@classify[2].target='Express'
qos.@classify[2].ports='5190'
qos.@classify[2].comment='AOL, iChat, ICQ'
qos.@default[0]=default
qos.@default[0].target='Express'
qos.@default[0].proto='udp'
qos.@default[0].pktsize='-500'
qos.@reclassify[0]=reclassify
qos.@reclassify[0].target='Priority'
qos.@reclassify[0].proto='icmp'
qos.@default[1]=default
qos.@default[1].target='Bulk'
qos.@default[1].portrange='1024-65535'
qos.Default=classgroup
qos.Default.classes='Priority Express Normal Bulk'
qos.Default.default='Normal'
qos.Priority=class
qos.Priority.packetsize='400'
qos.Priority.avgrate='10'
qos.Priority.priority='20'
qos.Priority_down=class
qos.Priority_down.packetsize='1000'
qos.Priority_down.avgrate='10'
qos.Express=class
qos.Express.packetsize='1000'
qos.Express.avgrate='50'
qos.Express.priority='10'
qos.Normal=class
qos.Normal.packetsize='1500'
qos.Normal.packetdelay='100'
qos.Normal.avgrate='10'
qos.Normal.priority='5'
qos.Normal_down=class
qos.Normal_down.avgrate='20'
qos.Bulk=class
qos.Bulk.avgrate='1'
qos.Bulk.packetdelay='200'
rpcd.@login[0]=login
rpcd.@login[0].username='root'
rpcd.@login[0].password='$p$root'
rpcd.@login[0].read='*'
rpcd.@login[0].write='*'
sysstat.sysstat=sysstat
sysstat.sysstat.log_history='7'
sysstat.sysstat.compressafter='10'
sysstat.sysstat.sa_dir='/var/log/sysstat'
sysstat.sysstat.zip='xz'
sysstat.sysstat.enabled='true'
system.@system[0]=system
system.@system[0].hostname='OpenWrt'
system.@system[0].timezone='UTC'
system.@system[0].log_buffer_size='64'
system.@system[0].log_size='4096'
system.@system[0].log_file='/var/log/system.log'
system.ntp=timeserver
system.ntp.server='0.openwrt.pool.ntp.org' '1.openwrt.pool.ntp.org' '2.openwrt.pool.ntp.org' '3.openwrt.pool.ntp.org'
system.ntp.enabled='1'
system.ntp.enable_server='0'
ubootenv.@ubootenv[0]=ubootenv
ubootenv.@ubootenv[0].dev='/dev/mtd1'
ubootenv.@ubootenv[0].offset='0x0'
ubootenv.@ubootenv[0].envsize='0x10000'
ubootenv.@ubootenv[0].secsize='0x10000'
uhttpd.main=uhttpd
uhttpd.main.listen_http='0.0.0.0:80' '[::]:80'
uhttpd.main.listen_https='0.0.0.0:443' '[::]:443'
uhttpd.main.redirect_https='1'
uhttpd.main.home='/www'
uhttpd.main.rfc1918_filter='1'
uhttpd.main.max_requests='3'
uhttpd.main.max_connections='100'
uhttpd.main.cert='/etc/uhttpd.crt'
uhttpd.main.key='/etc/uhttpd.key'
uhttpd.main.cgi_prefix='/cgi-bin'
uhttpd.main.script_timeout='60'
uhttpd.main.network_timeout='30'
uhttpd.main.http_keepalive='20'
uhttpd.main.tcp_keepalive='1'
uhttpd.main.ubus_prefix='/ubus'
uhttpd.px5g=cert
uhttpd.px5g.days='730'
uhttpd.px5g.bits='1024'
uhttpd.px5g.country='ZZ'
uhttpd.px5g.state='Somewhere'
uhttpd.px5g.location='Uknown'
uhttpd.px5g.commonname='OpenWrt'
upnpd.config=upnpd
upnpd.config.enable_natpmp='1'
upnpd.config.enable_upnp='1'
upnpd.config.secure_mode='1'
upnpd.config.log_output='0'
upnpd.config.download='1024'
upnpd.config.upload='512'
upnpd.config.internal_iface='lan'
upnpd.config.port='5000'
upnpd.config.upnp_lease_file='/var/upnp.leases'
upnpd.config.uuid='c25b2336-a253-4ef7-acc4-b9d6797063c4'
upnpd.@perm_rule[0]=perm_rule
upnpd.@perm_rule[0].action='allow'
upnpd.@perm_rule[0].ext_ports='1024-65535'
upnpd.@perm_rule[0].int_addr='0.0.0.0/0'
upnpd.@perm_rule[0].int_ports='1024-65535'
upnpd.@perm_rule[0].comment='Allow high ports'
upnpd.@perm_rule[1]=perm_rule
upnpd.@perm_rule[1].action='deny'
upnpd.@perm_rule[1].ext_ports='0-65535'
upnpd.@perm_rule[1].int_addr='0.0.0.0/0'
upnpd.@perm_rule[1].int_ports='0-65535'
upnpd.@perm_rule[1].comment='Default deny'
wireless.radio0=wifi-device
wireless.radio0.type='mac80211'
wireless.radio0.channel='11'
wireless.radio0.hwmode='11ng'
wireless.radio0.path='platform/qca953x_wmac'
wireless.radio0.ht_capab='LDPC' 'SHORT-GI-20' 'SHORT-GI-40' 'TX-STBC' 'RX-STBC1' 'DSSS_CCK-40'
wireless.radio0.htmode='HT20'
wireless.radio0.disabled='0'
wireless.@wifi-iface[0]=wifi-iface
wireless.@wifi-iface[0].device='radio0'
wireless.@wifi-iface[0].network='ap'
wireless.@wifi-iface[0].ifname='wlan0'
wireless.@wifi-iface[0].mode='ap'
wireless.@wifi-iface[0].ssid='PEACG01_Ihvg'
wireless.@wifi-iface[0].encryption='psk2'
wireless.@wifi-iface[0].key='IMK5wrXC'
wireless.@wifi-iface[0].wps_pushbutton='1'</code>
</details>



===== OpenWRT =====

==== Download ====
[[http://netlab.dhis.org/download/software/openwrt/Perenio-PEACG01/|Perenio-PEACG01]]\\
[[https://github.com/rozhuk-im/openwrt/commits/all_local|github.com]]



==== Flashing ====

  * Copy **openwrt-ath79-nand-perenio_peacg01-initramfs-kernel.bin** into TFTP server root dir with name **0201A8C0.img**
  * TFTP server must listen on 192.168.1.10
  * Connect serial to top of the board, use 115200 speed
  * Power on device
  * Break boot by hitting **space** key
  * setenv bootslot 0
  * tftp
  * bootm
  * Wait untill OpenWRT boot
  * Use WebUI at 192.168.1.1 to update f/w




{{tag>hardware reverse linux openwrt ZigBee gateway}}
Net Lab

User Tools

Site Tools

Page Tools
